Right now you're trying to figure out whether this is something that runs a few hundred dollars or something that changes your month. The number swings on three things: where the mold is, how far it has spread, and what material it has grown into. This page lays out what we actually see when we quote this work in Ann Arbor, what the price ranges mean, and what drives them up or down.
What a mold remediation quote actually depends on
No two mold jobs price the same, and that is not a dodge. The biggest variable is location. Mold in a crawl space is a different animal than mold inside ductwork or behind bathroom walls, and each calls for different equipment, different containment, and different disposal. The second variable is the extent of the growth. A patch the size of a dinner plate on a rim joist takes a fraction of the time and material that widespread coverage across multiple surfaces does. The third variable is what the mold has gotten into. Porous materials like wood, drywall paper facing, or insulation typically have to come out. Nonporous surfaces like concrete or metal can often be cleaned and kept. When we come out to quote, we are measuring these three things and giving you a number that covers exactly what that house needs, not a template.
Ready for the work itself? Read about drywall mold removal. Need mold remediation in Ann Arbor? Start on our home page.
Crawl space mold remediation: what it runs
For mold that has settled in a crawl space, most of the work we do in Ann Arbor falls between $500 and $2,000. That range covers the majority of what we see: a defined area of growth on the rim joist, floor joists, or subfloor, where the mold is on wood or concrete and the affected area is manageable. The lower end of that range tends to be early-stage growth caught quickly, where containment is minimal and the surface can be scrubbed and dried in a single visit. The higher end covers larger areas, growth that has gotten into multiple structural members, or jobs where we are pulling out affected materials and disposing of them in sealed polyethylene waste bags before treating what remains. We always dry the work area thoroughly after removal and cleaning because moisture left behind is what lets mold come back.

HVAC system mold remediation: what it runs
When mold has grown inside ductwork or on components inside the furnace or air handler, the cost climbs significantly, and that is because the work is more involved and the risk of spreading spores through the house is higher if it is not done right. We are looking at $3,000 to $10,000 for HVAC mold remediation. The lower end covers cases where the growth is localized to a short run of duct or a single component, accessible without major demolition, and can be treated with targeted cleaning and HEPA-filtered equipment. The higher end covers extensive ductwork colonization, growth that has reached the air handler or multiple branches, or jobs where we are opening sections of duct to access and treat the interior. We use a wet vacuum to collect any standing water before we clean, and we run negative-pressure filtration throughout the work so disturbed spores get pulled through HEPA filters and are not pushed into your living spaces.
What makes the price move in either direction
Beyond the location and square footage, a few things routinely push a quote higher. The first is accessibility. If your crawl space is sealed, low, or has stored items that need to be moved, that takes time and we account for it. If your ductwork has tight bends or sections buried behind finished walls, we may need to open access points. The second is how wet things got and for how long. A one-time plumbing leak that was fixed quickly is a different job than chronic dampness from a foundation seepage issue, which is more common in Ann Arbor given the local soils. Poorly drained soil around the foundation means water sits against the basement or crawl-space walls longer after rain or snowmelt, and that drives recurring moisture and, eventually, mold. If the underlying moisture source is not addressed, we will tell you that before we start the remediation, because cleaning mold off a wet surface is a temporary fix.
What you do not necessarily need this for
If you have a small patch of mold on a hard, nonporous surface, like tile or a shower curtain, and you caught it early, that is often something you can handle yourself with a detergent solution, a scrub, and thorough drying. Mold on a nonporous surface is different from mold that has grown into porous material. If the mold is on bare concrete block or a metal duct exterior and it has not penetrated the material, wiping it down, letting it dry completely, and controlling the moisture source may be enough. If it has spread into wood fiber, insulation, or drywall paper facing, that is when you need a remediation crew with containment equipment, proper disposal, and the ability to dry the substrate before anything goes back in.
What happens on the first call
On the phone we can give you the typical range for crawl space or HVAC work, and the exact number gets confirmed once we've seen the job. You describe what you found or what you were told, where it is, and how large an area you are talking about. Our questions stick to size, location, and whether water was involved, and if it's work we handle, we book a time to see it in person. That visit is when we measure, assess the substrate, and determine what can be cleaned versus what has to come out. The written quote comes after that visit and before any work begins, priced on what we find in the space with no cushion added. Nothing gets decided on that call beyond booking the visit.
What the Job Includes
For work like this, the job can include:
- Repair the leak or humidity problem so the moisture condition that supported mold growth is addressed.
More Ways We Can Help
Updated November 2026